Search results for: 'Pump elements'

<div><p>Compact HYDAC design and inexpensive solution</p><ul><li> Bell housing in accordance with VDMA 24561 Form C</li><li> Unproblematic replacement of the forms A, B and C with one another possible in accordance with VDMA 24561</li><li>Can be supplied for almost all hydraulic pumps</li><li>Processing of both flange-mounting sides finished</li><li> Bell housing with damping and cooling element (air-oil cooler)</li><li> Fan wheel (mounted on the motor shaft) included in the scope of delivery</li><li>For 2-pole, 4-pole, 6-pole IEC standard motors (1000–3000 rpm)</li><li> Design B5, B35, V1, V15</li><li> Mineral oil in accordance with DIN 51524, other media upon request</li><li> With optional bell support foot bracket</li><li> Horizontal or vertical installation possible</li></ul></div><div><p>Cooling element:</p><ul><li>Supply and discharge with G3/4", gasket-sealing</li><li>Max. 16 bar operating pressure</li><li>Max. permitted oil temperature +100°C</li><li>The maximum temperature difference between oil inlet and ambient temperature may not exceed 50°C</li></ul><p>Delivery programme:</p><ul><li> Series 2001 for motor size 80 (0.55–0.75 kW with 1500 rpm)</li><li> Series 200 for motor size 90S – 90L (1.1–1.5 kW with 1500 rpm)</li><li> Series 250 for motor size 100L – 112M (2.2 – 4 kW with 1500 rpm)</li><li> Series 300 for motor size 132S – 132M (5.5 – 7.5 kW with 1500 rpm)</li><li> Series 350 for motor size 160M – 160L (11 – 15 kW with 1500 rpm)</li><li> Series 3501 for motor size 180M – 180L (18.5 – 22 kW with 1500 rpm)</li></ul></div>

<p>Recirculation cooler filtration units (UKF) are compact systems made up of boost pump, filter and plate heat exchanger for offline cooling-filtration circuits. The continuous cooling and filtration in the bypass flow can significantly increase the service life of the oil and the hydraulic system.</p><ul><li class="li-square">Constant temperature (independent of the cycle times of the hydraulic system)</li><li class="li-square">Uniform supply quantities</li><li class="li-square">Avoidance of pressure surges in the heat exchanger</li><li class="li-square">Filter element replacement without shutting down the hydraulic system</li></ul><p>Cooling and lubrication of gears<br />UKF with gear pump, duplex filter and plate heat exchanger.<br />The thermal bypass valve ensures that the system can start up even at lower temperatures.<br />In order to ensure a constant oil temperature, a closed-loop water volume controller can also be installed. This controller ensures that only the volume of water required to achieve the desired oil temperature is fed to the plate heat exchanger.</p>

<p>The compact and stationary fluid care units of the OLF 5 are used for fine filtration of hydraulic and lubricating oils in the bypass flow. Versions with motor-pump unit are also available. The toploader variant is characterised by the "upward" element removal (tool-free element change).</p><p>The OLF 5 is used, for example, on machine tools, plastic sharpening machines, mobile devices and in wind power.</p><ul><li class="libreak">Flow rate: max. 15 l/min</li><li class="libreak">Operating pressure: max. 4.5 bar</li><li class="libreak">Improved component and system filter service life</li><li class="libreak">Increased machine availability</li><li class="libreak">Longer oil change intervals</li><li class="libreak">Minimum space requirement due to compact design</li><li class="libreak">High service-friendliness</li><li class="libreak">High dirt absorption capacity of the elements (optionally also water)</li><li class="libreak">Environmentally friendly element disposal thanks to incinerability</li></ul>

<p>The compact and stationary fluid care units of the OLF 5 are used for fine filtration of hydraulic and lubricating oils in the bypass flow. Versions without motor-pump unit and tank installation variants are also available. The top-loader variant is characterised by the "upward" element removal (tool-free element change).Optionally integrated fluid sensor technology allows simultaneous monitoring of solid contamination, water saturation and temperature in the oil.</p><ul><li class="libreak">Flow rate: max. 15 l/min</li><li class="libreak">Operating pressure: max. 4.5 bar</li><li class="libreak">Improved component and system filter service life</li><li class="libreak">Increased machine availability</li><li class="libreak">Longer oil change intervals</li><li class="libreak">Minimum space requirement due to compact design</li><li class="libreak">Environmentally friendly element disposal thanks to incinerability</li></ul>